Omnitron-systems-technology iConverter 10/100M2 Plugin Module Manual de usuario descargar pdf

iConverter 10/100M2 Plug-in Module QUICK START GUIDE

The iConverter

10/100M2 is a carrier-class media converter and

a Network Interface Device (NID) that provides 10BASE-T or

100BASE-TX (10/100) to 100BASE-FX Fiber media conversion

with integrated management.

The 10/100M2 has built-in Operation, Administration and

Maintenance (OAM) functionality enabling the 10/100M2 to operate

as a managed demarcation point at the customer premises and

network edge, offering Quality of Service capabilities.

The 10/100M2 module can be managed using NetOutlook

SNMP

Management Software, Telnet or the Command Line Interface

(CLI).

For the complete User Manual on this product, access Omnitron’s

secure download site and request access.

http://www.omnitron-systems.com/login.php

INSTALLATION PROCEDURE

1) Congure DIP-Switches

2) Install Module in Chassis and Connect Cables

3) Congure Module via Command Line Interface

4) Verify Operation

1) CONFIGURE DIP-SWITCHES

DIP-SWITCH BANK 1

SW1 - UTP/FIBER PAUSE ENABLE

When this DIP-switch is in the Left “OFF” position,

Pause is disabled. When the DIP-switch is in the

Right “PAUS” position Pause is enabled.

When a port is congured for Auto-Negotiation

(AN), Pause operation is determined during the

negotiation process between itself and the link

partner. The port advertises its Pause capability

(Symmetrical or No Pause) based on the Pause

Disable/Enable DIP-switch setting.

When a port is operating in Manual mode (MAN),

its Pause operation mode is based on the Pause

Disable/Enable DIP-switch setting.

SW2 - FIBER FULL/HALF DUPLEX

Setting this DIP-switch to Half-Duplex “HDX”

facilitates a connection that supports Half-Duplex.

Setting this DIP-switch to Full-Duplex “FDX”

facilitates a connection that supports Full-Duplex

operation.

Once connected, press <ENTER> to bring up a command line prompt on the attached

PC.

Management Options iConverter, Serial Agent

Network Management

1: Chassis and Module Management

2: Set Module Name Preferences

Management Module Preferences

3: IP and Control Preferences

4: SNMP Preferences

5: Abandon Preference Changes

6: Save Preference Changes

7: Restore Factory Defaults

8: Restart Management Module

9: Other Networking Features

Management Module Maintenance

10: Firmware Update

11: Set Date/Time

IP Address = 192.168.1.220

Chassis Number = 1

Enter Choice, <H>elp, E<x>it >

Figure E: Command Line Interface Menu Options

The CLI interface allows for the detailed conguration of the module. It is recommended

to congure the module with an IP address associated with the attached network.

Also, SNMP traphost address should be congured if the module is managed with an

SNMP-based Management System. See the 10/100M2 User Manual for complete

information.

4) VERIFY OPERATION

Once the module has been

installed and configured per

steps 1 - 3, verify the module is

operational by viewing the LED

indicators.

The Power LED indicates the

modules is receiving power from

the chassis.

The Fiber Optic link LED indicates

the ber optic connection has

been established.

The UTP link LED indicates

the module has established

a connection across its UTP

port.

Figure A: DIP-Switch Locations

Form 040-8900N-002 D 9/13

Omnitron Systems Technology * 38 Tesla * Irvine, CA 92618

949.250.6510 tel * 949.250.6514 fax * www.omnitron-systems.com

Figure F: LED Indicators

Page 1

LED Function

“Legend”

Color OFF State ON / Blinking State

Power “Pwr” Green No power Module has power

Power Supply

Status “PSx”

Green

Power Supply not

installed

ON: Power Available

Blinking: No power available

from “PSx”

Network Ports Status*

Fiber Optics “FO” Green No Fiber Link

ON: Fiber link is active

Blinking: Fiber Data Activity

Master/Slave “BP” Green Slave Mode Master Mode

10Mbps UTP “10” Green

10Mbps not selected or

disconnected

ON: Active 10Mbps UTP link

Blinking: UTP Data Activity

100Mbps UTP

“100”

Green

100Mbps not selected

or disconnected

ON: Active 100Mbps

UTP link

Blinking: UTP Data Activity

UTP Full-Duplex

“FDX”

Green Half-Duplex Full-Duplex

1 2

Indice de contenidos

Pagina 1 - 4) VERIFY OPERATION

iConverter 10/100M2 Plug-in Module QUICK START GUIDEThe iConverter®10/100M2 is a carrier-class media converter and a Network Interface Device (NID) th

Pagina 2 - DIP-SWITCH BANK 2

DIP-switch is in the RIGHT “EN” position, the Backplane Port is enabled. This allows Ethernet Backplane connectivity to an adjacent module via the ch

Comentarios a estos manuales

Sin comentarios

Omnitron-systems-technology iConverter 10/100M2 Plugin Module Manual de usuario

Busca en linea o descarga Manual de usuario para Comunicación Omnitron-systems-technology iConverter 10/100M2 Plugin Module. Omnitron Systems Technology iConverter 10/100M2 Plugin Module User Manual Manual de usuario

Indice de contenidos

Comentarios a estos manuales

Relacionado con productos y manuales para Comunicación Omnitron-systems-technology iConverter 10/100M2 Plugin Module